Article

How much does Wazer cost?

November 27, 2025 - By 
WAZER,The First Desktop Waterjet Cutter

Compact waterjet pricing starts at $7499.

Just so, how much is a Wazer?

It's the only desktop machine that cuts virtually everything, including steel, titanium, aluminum, glass, stone, tile and carbon fiber. Traditional waterjets cost upwards of $100,000 and are too large and messy to fit in most workshops. WAZER costs $7,500.

Also, is water jet cutting expensive? The typical price range for a waterjet with a single cutting head is approximately USD$100-135 per hour, though high-end parts can run up to $2,000 per hour depending on material type and thickness as well as part geometry.

Correspondingly, how much does a waterjet cost?

👉 For more insights, check out this resource.

While there are several factors that can affect the hourly cost of running a waterjet, on average, it can cost anywhere between $20/hr – $40/hr to run a waterjet with a single abrasive cutting head at 60,000 psi (does not include labor or capital repayment).

Can a waterjet cut glass?

👉 Discover more in this in-depth guide.

Generally speaking, higher quality glass that is thicker tends to be easier to cut than low quality glass or thin glass. Tempered glass is impossible to cut with a waterjet, as the glass is under stress. When you begin cutting it, tempered glass will shatter into many small fragments.

What materials can water jets cut?

Materials commonly cut with a water jet include textiles, rubber, foam, plastics, leather, composites, stone, tile, glass, metals, food, paper and much more. “Most ceramics can also be cut on an abrasive water jet as long as the material is softer than the abrasive being used (between 7.5 and 8.5 on the Mohs scale)”.

How much pressure does a water jet have?

Faster feed rates are used to prevent the jet from cutting all the way through. The water pressure is typically between 20,000 and 55,000 pounds per square inch (PSI). The water is forced through a 0.010″ to 0.015″ in diameter orifice (hole) in a jewel.

How does a waterjet work?

A waterjet cutter is a tool capable of slicing into metal or other materials using a jet of water at high velocity and pressure, or a mixture of water and an abrasive substance. The process is essentially the same as water erosion found in nature but accelerated and concentrated by orders of magnitude.

What can a waterjet not cut?

Among the very few materials that waterjets cannot cut are diamonds and tempered glass. Some composite materials (layers of different materials sandwiched together) can't be cut because the water can seep between the layers and “delaminate” the material. Many composite materials cut just fine.

How much is a CNC router?

CNC Router Average Costs

The most basic of three-axis models sell for anywhere from $5,000 to $10,000. Mid-range machines used for panel processing and signage are likely to cost anywhere from $25,000 to $50,000. High-end machines often cost $50,000 to $150,000.

How thick can waterjet cut?

What is the maximum material thickness that can be cut with water jets? For metals, the maximum thickness is normally 150 mm (6″). Waterjet cutting has also been used in special applications where materials up to 400 mm (15.75″) thickness are cut.

How thick of steel can a waterjet cut?

Material thickness. For soft materials, you can cut extremely thick pieces. For example, you can cut two foot thick (0.6 m) sponge easily. Practically speaking 2″ (5 cm) to 3″ (7.5 cm) thick steel is about the upper thickness limit for an abrasive waterjet.

Is laser cutting expensive?

This type of laser is strong enough to cut and engrave almost anything, giving you the flexibility you need. However, high wattage laser cutting machines are generally much more expensive than entry level units. You can pay anywhere from $10,000 to $50,000 for some models.

How much water does a waterjet use?

Waterjets use between one half and five gallons (2 to 19 liters) of water per minute when cutting. Some of that water is used to cut and some of it is used to cool the pump.

Can you waterjet acrylic?

As mentioned before waterjet cutting is used is almost every industry due to its capability to cut almost any material relatively cheaply, all without altering the properties of the material. Materials ranging from 0.010″ acrylic all the way to 10” thick stainless steel can be cut by waterjet.

Who invented the water jet cutter?

Dr. Norman Franz

Is laser cutting cheaper than water jet?

$20/hr * 16.67 hr = $333.40 for 15,000″ of cutting. Without considering any other factors, waterjet cutting is more than 5x the cost of laser cutter cost per hour.

What can cut a diamond?

Diamond cutting is done by cleaning or sawing the diamond with a steel blade or a laser like the Sarine Quazer 3. The rough diamond is usually placed in a wax or cement mold to hold it in place and then cleaved along its tetrahedral plane, its weakest point. If no point of weakness exists, instead sawing is used.

How accurate is a water jet cutter?

Relatively speaking, a water jet cutting process is highly accurate. Once the cutting starts (meaning that the initial through hole is complete), a waterjet cutting machine can achieve a parts tolerance of +/- 0.001” with consistency. This makes the waterjet cutting process highly desirable for cutting precision parts.

What is water jet cutting process?

Water Jet cutting uses an ultra-high pressure stream of water to carry an abrasive grit. The abrasive does the cutting through a mechanical sawing action, leaving a smooth, precision cut surface. Waterjet is the most versatile process, because it is able to cut almost any type of material.

Can you cut glass with a laser?

Yes, depending on the type and thickness of glass, and what you mean by cut. For thicker glass, lasers are used in conjunction with surface cooling to cause the glass to fracture along the laser line (Laser cutting of float glass during production and Zero Width Glass Cutting with CO2 Laser).

How do I cut a hole in glass?

Tape a small scrap of dense cardboard to the glass. Begin at very low rpm to create a dimple in the glass, then remove the cardboard and continue at about 400 rpm. Drilling a hole in a pane of glass or a mirror is simple. The key is to use a carbide bit made especially for glass and tile (see photos).